In Doing Service Mobile Phone Service is needed or the understanding of what tools we will use, especially if it is about software, this software because it takes understanding who is more than At The Deep Understanding in the field of Hardware.:.
TORNADO UFS TECHNIQUES
Tips and Tricks On Using Tornado UFS3 Nokia
In the case of 1st Boot Err or Bad Resp DCT3
Damage like this is common because it is not terhubungnya between Box by phone
Check the flasher cable is used, because it is possible there is a broken line
If the cable is in good condition, there may be some damage to the software UFS3
Reinstall the program with data that is still good
In Case of Contact Service
Damage such as this usually occurs because of damage data
Perform data removal process with Erase FLASH
Then do flashing with data that is still good
Put a tick in the UI Options and click the Settings UI
If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings
If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA
If sata or Erasing Flashing process, the process stalled
Check the flasher cable, because it shows breakdown of the relationship between cellular telephone with Flasher Box
Repeat process with reducing speed Speed Flasher
If it still stops at the same position repeatedly, it is possible to crash the Flash IC
In the case of failed Phone blimking contact retailers or on the phone type WD2
Make sure the phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run the program for Nokia phones and select the type of WD2
Choose a type mobile phone that is being repaired
Click the Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button Check to make sure the phone had been connected "Boot Ok"
In the UI Settings column select Normal, wait until the Normal Mode Ok
After appearing on the screen Normal Mode Ok continue by pressing the Format User Area
Finish Process
Practical Solutions Contact retailer or Blimking on Nokia 6600 mobile phone
If at the time of Flashing occurs Erase error
Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000
If there Erase Flash Error then have to replace the flash IC No. 2, from 4 existing IC
If the process is successful, but when power was still at the Contact retailer
Lift battry then plug it in again, then press the Call button on Hanphone or green button + * + number 3 on the mobile phone by simply pressing together, without using the sim card
After the above steps have been made, then the phone will do the formatting
After doing the formatting, mobile phones have been ready for use
In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2
Make sure the phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run the program for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repaired
Click the Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button Check to make sure the phone had been connected "Boot Ok"
In the UI Settings column select Normal, wait until the Normal Mode Ok
After appearing on the screen Normal Mode Ok proceed by giving the Init Simlocks checklist contained in the columns UI Options
Then click the Settings UI to appear on the screen Ok Init Simlock
In the case of No Charging and No Signal On Phone type and DCT-4 WD2
Make sure the phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run the program for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repaired
Click the Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button Check to make sure the phone had been connected "Boot Ok"
In the UI Settings column select Normal, wait until the Normal Mode Ok
Click the button write pm (Wr PM), only 1 time with a provision has been saved PM file from each phone in the directory (C: \ Program files \ Nokia \ Phoenix \ Products)
Wait until the process is complete
To overcome the problem Phone Locks on the phone type Nokia
Make sure the phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run the program for Nokia phones
Choose a type mobile phone that is locked or the phone lock
Click the Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button Check to make sure the phone had been connected "Boot Ok"
Put a tick in the Full Factory Devaults contained in the columns UI Options
Then click the Settings UI to appear on the screen Full Factory Devaults Ok
Tips and Tricks Using UFS3 Tornado On Sony Ericsson phones
Practical Ways Sony Ericsson Flashing
Make sure the phone is connected well with UFS3 Tornado Box
Click the Connect button located on the top left of the program
Battery should not be installed first before pressing the ON button, after pressing the button on your new pair of batteries, wait until all information completely legible phone
Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the cell phone under construction
How to unlock Z200 Unlock
In this case we can start by pressing the Init Locks on UFS3 Tornado
Followed by mereflash re-file "Z200_cust_std.bis by pressing the flash button on the program Cust UFS3 Tornado
Or by setting up the scenario to choose Unlock column by pressing the Go button
Flashing Sony Ericsson Z200 Series Type ATRZ
Enter the file or data such as language and 200_126734_r6c_fix3 200_126734_r6c_con3.bis on in part2 part1
Connect the phone with flasher box and press the Go button
Wait until the finish, to end press the Stop button and the phone ready to be released
Flashing Sony Ericsson T610 series RTP Type
Enter the MCU file such as modem files T610_132233_r4c003_Emea6.bis and T610_132233_r4c003_modem.bih
Select the column scenario MCU + Modem
Connect phone and press the Go button, wait until the process is complete
Click Stop to release mobile phone
Tips and Tricks Using UFS3 Tornado on Samsung phone
Make sure the phone is connected well with UFS3 Tornado Box
Click the Connect button located on the top left of the program
Choose a type mobile phone that will be flashed and also select the appropriate data type phones that do
Enter the file flasher according to the type of phone that worked
Disconnect the battery (flash without battery)
Press the 'Write Flash' contained in the program UFS3 Tornado and continue by pressing the 'on' on the phone until the flame jgn
Wait until flash process is complete
To type a specific phone or cell phone batteries remain attached long time in the flash
GOOD USEFUL
compaq presario CQ5300F
compaq presario motherboard
